A twelve-storey office refit usually ends the same way: one bid specifies a cable driven traction elevator, another proposes a hydraulic unit, and both look acceptable on paper. For a building of that height, the cable-driven machine is the right default — it copes with the travel, absorbs the morning traffic and keeps running costs predictable — but only if the rope system, machine position and shaft dimensions are settled before the contract rather than during installation. Most of the trouble we see on site comes from treating a traction elevator as a commodity box instead of a friction system with measurable limits.
Content
- 1 What a Cable-Driven Elevator Actually Is
- 2 Roping, Gearing and Machine Placement Set the Performance Envelope
- 3 Cable Driven versus Hydraulic: Where Each One Fits
- 4 Safety Elements to Confirm in the Submittal
- 5 Matching Load, Speed and Traffic to the Building
- 6 Plan for Ropes and Sheaves as Wear Items
- 7 Specification Mistakes That Cost Money Later
What a Cable-Driven Elevator Actually Is
In industry language, a cable driven elevator is a traction elevator. The car hangs from a set of steel wire ropes — commonly four to eight — that pass over a grooved traction sheave driven by an electric motor, with the other end anchored to a counterweight. The counterweight is normally sized at car weight plus roughly 40 to 50 percent of rated load, so the motor only has to move the imbalance between car and counterweight rather than the whole mass.
The important detail is that the ropes are not wound onto a drum. Movement comes from friction between rope and sheave groove. A winding-drum machine is a different, now rare design with a limited travel range. Because traction depends on friction, rope tension, groove condition and load balance all matter: an overloaded car, a badly matched counterweight or a worn groove can allow slip, and slip shows up as starting jolts, levelling errors and, eventually, damaged rope.
- Traction machine: motor, brake and sheave in one assembly
- Suspension ropes with terminations and equalising springs
- Counterweight frame, fill weights and its own guide rails
- Car sling, platform and car guide rails
- Overspeed governor, safety gear and oil buffers
- Controller, drive and door operator
Roping, Gearing and Machine Placement Set the Performance Envelope
Two elevators with the same rated load and speed can behave very differently depending on three choices made at the design stage.
1:1 versus 2:1 roping
With 1:1 roping the rope travels at car speed and runs straight from car to sheave to counterweight. It is mechanically simple and has fewer rotating sheaves to inspect, but the machine carries the full rope load. With 2:1 roping the rope is reeved through sheaves on the car and counterweight, so it travels twice the car speed and each rope strand carries roughly half the load. That allows a smaller, lighter machine and lower shaft loads, at the cost of more rope bends and more pulleys to maintain. On high-rise projects, 2:1 is often the only practical way to keep the machine within the overhead envelope.
Gearless versus geared machines
Gearless permanent-magnet synchronous machines dominate from around 1.0 m/s upward: quieter, more efficient, and compact enough for machine-room-less layouts. Geared machines still make sense for low-speed, heavy-duty freight work or where budget dominates. Ask which type is being quoted, because the two have different spare-part profiles and different heat output in the shaft.
Machine room or machine-room-less
A machine-room-less design places the machine inside the shaft headroom and frees floor area that would otherwise be lost — valuable in residential and retail projects. The trade-off is a larger overhead requirement and heat dissipation into the hoistway. Confirm both overhead and pit depth against the builder's drawings early; adding 300 mm of overhead after the slab is poured is a structural project, not a drawing revision.
Cable Driven versus Hydraulic: Where Each One Fits
Hydraulic elevators remain a legitimate choice for low-rise, low-frequency duties, especially where a machine room cannot be created and the travel is short. Beyond that, the pumping losses, oil management and slower travel usually push the decision back to traction.
| Consideration | Cable-driven traction | Hydraulic |
|---|---|---|
| Practical travel | Effectively unlimited; strongest above six stops | Typically suited to low-rise travel |
| Typical speed | 0.4 m/s to 4 m/s and above | Usually below 1.0 m/s |
| Machine space | Machine room or shaft-headroom machine | Small power unit, often in a closet |
| Energy profile | Counterweight reduces motor work; regenerative drives possible | Continuous pumping, with heat generation |
| Ride quality | Smooth and consistent once levelling is tuned | Soft start, but noticeable temperature drift |
| Shaft demands | Overhead, pit and guide-rail loads must be checked | Lower overhead, but ram and oil management required |
| Maintenance focus | Ropes, sheave grooves, brake, governor | Oil condition, seals, power unit, valve |
| Best fit | Offices, hotels, hospitals, high-rise residential, heavy goods | Low-rise retrofits, occasional-use goods and car lifts |
Safety Elements to Confirm in the Submittal
A traction elevator's safety chain is well established, but it has to be visible on paper before delivery, not discovered during commissioning. Request the following in the technical submittal and confirm each item is code-compliant for the destination market:
- Overspeed governor with matched safety gear — progressive type for higher speeds
- Oil buffers sized to the rated speed and system mass
- Brake rated for the full suspended load, with monitored release
- Rope-slip and unintended car movement protection where the applicable code requires it
- Automatic rescue device that moves the car to a landing on power failure
- Door interlocks, light curtain and overload detection with audible warning
- Witnessed load test and inspection certificate from an accredited body
Matching Load, Speed and Traffic to the Building
Capacity is a traffic calculation, not a guess based on the number of floors. A residential tower with 90 apartments and a hospital with the same floor count have completely different demands: the hospital needs bed-sized cars, wider doors and priority control, while the residential block lives or dies on interval and handling capacity during the morning peak.
Collect the real inputs first: population per floor, peak arrival rate, acceptable waiting interval, stretcher or trolley dimensions, goods weight and pallet size, and the finished floor-to-floor heights. Only then pick the rated load and speed. A passenger elevator rated at 630 kg and 1.75 m/s is a common commercial starting point, while freight duties may need several tonnes and a reinforced car floor. Our own production range runs from 0.4 to 4 m/s and 50 to 10,000 kg, which is broad enough that the constraint is usually the shaft — pit depth, overhead, and guide-rail fixing — rather than the machine.
Plan for Ropes and Sheaves as Wear Items
Ropes are consumables. They are replaced on condition — broken wire counts, measured elongation, diameter loss, visible corrosion — not on a fixed calendar, and the sheave grooves wear with them. A groove that has become too deep or polished loses traction and accelerates rope damage, so inspections should record both rope and groove condition. Budget for the first rope replacement as part of the life-cycle cost rather than treating it as an emergency.
The same logic applies to the drive. Variable voltage and variable frequency control is standard on modern traction machines and delivers smoother starts, better levelling and lower peak current, but it depends on correct parameter setting at commissioning; a poorly tuned drive produces the jolts that owners later blame on the ropes.
Specification Mistakes That Cost Money Later
- Undersized counterweight to save cost, which overloads the motor and pushes slip risk up
- Sheave diameter chosen too small for the rope, which shortens rope life noticeably
- Overhead and pit dimensions copied from a template instead of measured on site
- No machine-room-less heat assessment, leaving the shaft and controller cabinet overheating in summer
- Warranty wording that excludes ropes and brake linings without stating it clearly in the offer
- Installation awarded to a team with no experience of that specific roping arrangement
Each of these is cheaper to resolve at tender stage than after handover, and each is verifiable with drawings, calculations and component certificates.
For most buildings above five or six stops, a cable driven traction elevator is the sensible baseline: efficient, well understood by service teams, and scalable from small residential units to heavy freight work. The decision that actually protects the project is not traction versus hydraulic — it is whether the roping, machine placement, shaft dimensions and maintenance plan are documented before the order is placed.











